Skip to Content

Shower channel

Highline. The accent in the floor.

A 3 mm stainless steel panel with a wide frame. Striking, robust and timeless, made for large formats and natural stone.

3 mmMaterial thickness of cover and frame
60 · 70 · 80 · 90 cmthree lengths
60–100 mmbuild height, adjustable

Build-up

Solid wherever you look.

Cover and frame are made from 3 mm stainless steel. The design is present but quiet, and stays a clear line in the floor even with large tiles and natural stone.

Frame and cover in stainless steel 1.4301, factory-fitted waterproofing membrane, abP-tested.

Exploded view

Five parts, one line in the floor.

Scroll: cover, hair catcher, channel body, trough and siphon come apart.

The textile waterproofing membrane is bonded to the plastic trough at the factory — it is already in place when the bonded waterproofing is applied.

Cover and channel body in 3 mm stainless steel 1.4301. The hair catcher lifts out for cleaning, the side DN 50 outlet keeps the installation height low.

Scroll: cover, hair catcher, channel body, trough and siphon come apart.

One line. Three rooms.

Keep scrolling: three views, one product.

A clear line in natural stone.Brushed surface, straight line, calm within the tile pattern.
Cleanly framed.The wide frame encloses the tile exactly.
A clear accent.Stainless steel, 3 mm, a straight line.

Technical data.

MaterialStainless steel 1.4301 / V2A (AISI 304), 3 mm
Lengths60 · 70 · 80 · 90 cm
Build height60–100 mm
Drain360° rotating drain pot, DN 50 outlet, trap
Drain capacity0.80 l/s (48 l/min) with the standard siphon, trap water height 25 mm
WaterproofingWaterproofing membrane fitted at the factory, abP
TestingabP, EN 1253
SiphonOutletTrap water heightDrain capacity
Y.8001Y.8001 (standard)horizontal25 mm48 l/min
Y.8082Y.8082horizontal30 mm48 l/min
Y.8081Y.8081horizontal50 mm60 l/min
Y.8002Y.8002vertical (downward)30 mm70 l/min

The drain capacities refer to the respective siphon.

Ordering information.

4 variants.

Item numberSize
LH8-H24L70E170 cm
LH8-H24L80E180 cm
LH8-H24L90E190 cm
Made for your project — special lengths, finishes, sizesNot held in stock; lead time on request.
LH8-H24L60E1Project60 cm

Identical for every variant: Surface Brushed stainless steel · Material Stainless steel 1.4301 / V2A (AISI 304) · Outlet DN 50

Special lengths on request. Every channel can be cut to size on site.

Installation in five steps.

The order follows the site: shell first, tile last.

ShellPosition the channel, connect it to the drainage and set the height.
Screed workLay the screed with a fall towards the channel; the protective cover sets the height.
WaterproofingRemove the protective cover and bond the waterproofing membrane into the bonded waterproofing.
Tiling workTile the floor with a fall towards the channel and grout the joints.
CoverInsert the cover and peel off the protective film last.

Installation

Installation step by step.

Twelve steps from the pipe connection to the finished joint. Click a step or let it run.

Connect the drain body
1Connect the drain bodySet the drain body in place and push the spigot into the waste pipe. The fixing brackets and screws are optional.
Align it
2Align itFix the position to the wall and level the channel with a spirit level.
Cut the spigot to height
3Cut the spigot to heightShorten the spigot, deburr the cut edge and soap the seal before joining.
Check for leaks
4Check for leaksPour in water and check the connection for tightness before building it in.
Lay the screed
5Lay the screedBring the screed up to the channel with a fall of 1–2 % towards it.
Remove the protective cover
6Remove the protective coverTake off the building protection cover and fold the factory-fitted membrane outwards.
Bed in the membrane
7Bed in the membraneBed the membrane into the adhesive and press it out flat onto the floor.
Apply the bonded waterproofing
8Apply the bonded waterproofingRoll the waterproofing onto the floor first, then up the wall.
Tile the floor
9Tile the floorLay the floor tiles up to the channel.
Cut the cover to length
10Cut the cover to lengthMeasure, shorten the cover with an INOX disc, deburr the edge and dispose of the offcut.
Fit the cover
11Fit the coverSet the cover into the channel and check that it sits flush with the tiles.
Seal the joint
12Seal the jointClose the perimeter joint with sanitary silicone.

Frequently asked questions.

Which lengths is Highline available in?

60, 70, 80 and 90 cm.

What is Highline made of?

Stainless steel 1.4301 / V2A (AISI 304), 3 mm thick.

Which build height does Highline need?

60 to 100 mm, measured from the top of the waterproofing membrane.

How much water does Highline drain?

0.80 l/s, that is 48 l/min, with the standard siphon. The trap water height is 25 mm.

Is Highline suitable for bonded waterproofing?

Yes. The waterproofing membrane is fitted at the factory. Highline is tested to EN 1253 and holds a German abP.

How is a Highline item number put together?

LH8-H24L80E1 stands for the 80 cm channel in brushed stainless steel; L60, L70, L80 and L90 are the four lengths.

Specification text for tenders.

Ready to paste into your bill of quantities (German, as used in German tenders).

Duschrinne Fabrikat Gruen, Typ Highline, oder gleichwertig, bestehend aus Rinnenkörper und Abdeckung aus Edelstahl 1.4301 (V2A), Materialstärke 3 mm, Oberfläche gebürstet, mit herausnehmbarem Haarsieb, 360° drehbarem Ablauftopf und Geruchsverschluss (Sperrwasserhöhe 25 mm), seitlicher Abgang DN 50. Dichtmanschette werkseitig mit der Kunststoffwanne verbunden, für Verbundabdichtung geeignet. Ablaufleistung 0,80 l/s nach EN 1253, abP-geprüft. Länge ____ cm (60 / 70 / 80 / 90), vor Ort kürzbar. Art.-Nr. LH8-H24L__E1.

Copy text