Skip to Content

Produktbeschreibung

This tileable shower tray from GRUEN is a sloping board with a shower drain and sealing membrane for creating level showers. The surface of the substrate is inclined towards the drain with a slope of ≥2°. It is compatible with the GRUEN linear drainage system, which is included in the set. The shower tray is consistently designed to be very easy, fast, and safe to install: it can be cut comfortably and precisely to the required size based on the applied grid pattern. Thanks to its intelligent components, it can easily compensate for height differences and be securely attached to almost all drainage systems. The sealing membrane is securely connected with a closure ring. It hangs over the sides and already creates a secure seal up to the wall area without any piecing. The adjustable screw ring serves to adapt to tile pattern and height. The Nova cover has a closed stainless steel surface. When used upside down, it can be tiled and visually disappears into the tile surface. With the tileable shower tray with point drainage from GRUEN, you can create perfect and beautiful shower areas.

 


Waterproof Guarantee

 


Comfortably Cuttable

 


Easy and time-saving installation.  

measure and cut

Messen Sie die Duschfläche aus und schneiden Sie das Duschelement passend zu. Ein Kürzen der Dichtungsbahn ist nicht erforderlich.   


System an Abfluss anschließen und Dichtungsbahn verlegen

Verlegen Sie die Abdichtbahn bis in den Wandbereich. Verbinden Sie das Entwässerungssystem mit Rohrverbinder und Verschlussring.  

Use the height-adjustable screw ring to adjust the height of the floor drain to match the tile surface.

Differences in height of the surface covering can be accommodated by rotating the adapter.

Cover Usage

Nova

The Nova cover presents an elegant, closed stainless steel surface.    



Nova — flipped

Turned upside down, the same Nova cover can be tiled and disappears into a continuous tile pattern.




Components in the set

 


Frequently asked questions.

What is the tileable shower element with linear drainage?

A sloping board for level-access showers whose surface falls towards the channel with a slope of at least 2 degrees.

Is the shower channel included?

Yes. A GRUEN linear drainage system is included in the set.

Can the element be cut to size?

Yes. A printed grid pattern allows it to be cut comfortably and precisely on site.

How is it sealed?

The sealing membrane is applied at the factory and connects directly to the bonded waterproofing.

Can height differences be compensated?

Yes. The components compensate height differences and allow a secure connection to almost all drainage systems.

Installation

Installation step by step.

Eleven steps from measuring to the finished joint. Click a step or let it run.

Measure the shower area
1Measure the shower areaMeasure the shower area (X / Y). The QR code leads to the installation video.
Cut the board to size
2Cut the board to sizeCut the sloping board along the printed grid and keep the direction of fall.
Connect the drain
3Connect the drainSet the drain body, connect it to the waste pipe and check the connection for tightness.
Fit the board
4Fit the boardBed the board in the adhesive and push it onto the drain until it audibly clicks.
The board carries foot traffic
5The board carries foot trafficOnce bedded, the board can be walked on and worked on directly.
Apply the bonded waterproofing
6Apply the bonded waterproofingBring the waterproofing over the board and into the corners, then cut the opening above the drain.
Set the drain pot
7Set the drain potPlace the drain pot into the opening.
Lock the clamping ring
8Lock the clamping ringInsert the clamping ring, turn it until it clicks and check that it is locked.
Fit the odour trap
9Fit the odour trapPush in the odour trap, turn it to lock and remove the transport part.
Tile and set the height
10Tile and set the heightTile up to the drain and adjust the height with the screw ring.
Seal the joint
11Seal the jointClose the perimeter joint with sanitary silicone.